<?XML Version="1.0">
<nidocument>
<nicomment>
<nifamily familyname="LabVIEW Simulation Module" displayname="LabVIEW Simulation Module">
</nifamily>
</nicomment>
<nierror code="-2375">
LabVIEW Simulation Module:  Auto Period is selected for simulation loop timing but the step size is not a multiple of the source clock period
</nierror>
<nierror code="-2374">
LabVIEW Simulation Module:  The negative slew rate must be less than or equal to the positive slew rate.
</nierror>
<nierror code="-2373">
LabVIEW Simulation Module:  The version of LabVIEW you installed for this embedded device supports only the 1 kHz timing source of the Simulation Loop.
</nierror>
<nierror code="-2372">
LabVIEW Simulation Module:  The index table for a lookup table (LUT) must be non-decreasing.
</nierror>
<nierror code="-2371">
LabVIEW Simulation Module:  The discrete sample period of each discrete function must be an integer multiple of the overall discrete step size of the simulation.
</nierror>
<nierror code="-2370">
LabVIEW Simulation Module:  A single-input single-output (SISO) state-space model requires a B matrix with only one column and a C matrix with only one row.
</nierror>
<nierror code="-2369">
LabVIEW Simulation Module:  The model you specified requires direct feedthrough.  Open the configuration dialog box of this function and set the Execution Mode parameter to Direct.
</nierror>
<nierror code="-2367">
LabVIEW Simulation Module:  The External Model Interface DLL returned an error.
</nierror>
<nierror code="-2366">
LabVIEW Simulation Module:  The External Model Interface Node returned an error.
</nierror>
<nierror code="-2365">
LabVIEW Simulation Module:  The order of the linear time-invariant (LTI) model must remain the same from the previous iteration.
</nierror>
<nierror code="-2364">
LabVIEW Simulation Module:  The dimension of the multiple-input multiple-output (MIMO) linear time-invariant (LTI) model must remain the same from the previous iteration.
</nierror>
<nierror code="-2363">
LabVIEW Simulation Module:  A state-space model with indirect feedthrough requires an empty or zero D matrix.
</nierror>
<nierror code="-2362">
LabVIEW Simulation Module:  The number of channels must match the number of inequality constraints.
</nierror>
<nierror code="-2361">
LabVIEW Simulation Module:  Insufficient number of user defined reference points.
</nierror>
<nierror code="-2360">
LabVIEW Simulation Module:  To use the Discrete States Only ODE solver, the simulation diagram must not contain any continuous functions.
</nierror>
<nierror code="-2359">
LabVIEW Simulation Module:  The discrete step size must be an integer multiple of the continuous step size.
</nierror>
<nierror code="-2358">
LabVIEW Simulation Module:  A discrete function cannot accept a continuous model.
</nierror>
<nierror code="-2357">
LabVIEW Simulation Module:  A continuous function cannot accept a discrete model.
</nierror>
<nierror code="-2356">
LabVIEW Simulation Module:  The sample period (sec) parameter must be either -1 or positive.  If the sample period (sec) parameter is positive, the sample skew (sec) must be greater than or equal to 0 and less than the sample period (sec).
</nierror>
<nierror code="-2355">
LabVIEW Simulation Module:  The value of the Decimation parameter for the Collector function must be greater than or equal to 1.
</nierror>
<nierror code="-2354">
LabVIEW Simulation Module:  The number of elements in the input array does not equal the number of columns in the gain matrix. 
</nierror>
<nierror code="-2353">
LabVIEW Simulation Module:  You cannot change the maximum delay while the simulation is running.
</nierror>
<nierror code="-2352">
LabVIEW Simulation Module:  The delay must be less than or equal to the specified maximum delay.
</nierror>
<nierror code="-2351">
LabVIEW Simulation Module:  The specified parameter is a vector.  Enter a vector value.
</nierror>
<nierror code="-2350">
LabVIEW Simulation Module:  The specified parameter is a scalar.  Enter a scalar value.
</nierror>
<nierror code="-2349">
LabVIEW Simulation Module:  The parameter name is not in the specified parameter list.
</nierror>
<nierror code="-2348">
LabVIEW Simulation Module:  The given State Derivatives parameter is incompatible with the specified subsystem.
</nierror>
<nierror code="-2347">
LabVIEW Simulation Module:  The given Outputs parameter is incompatible with the specified subsystem.
</nierror>
<nierror code="-2346">
LabVIEW Simulation Module:  The given Inputs parameter is incompatible with the specified subsystem.
</nierror>
<nierror code="-2345">
LabVIEW Simulation Module:  The given States parameter is incompatible with the specified subsystem.
</nierror>
<nierror code="-2344">
LabVIEW Simulation Module:  The given Outputs parameter is incompatible with the specified subsystem.
</nierror>
<nierror code="-2343">
LabVIEW Simulation Module:  The given Inputs parameter is incompatible with the specified subsystem.
</nierror>
<nierror code="-2342">
LabVIEW Simulation Module:  The given States parameter is incompatible with the specified subsystem.
</nierror>
<nierror code="-2341">
LabVIEW Simulation Module:  The initial time of the simulation cannot be greater than or equal to the final time.
</nierror>
<nierror code="-2340">
LabVIEW Simulation Module:  The linearizer detected an internal error.
</nierror>
<nierror code="-2339">
LabVIEW Simulation Module:  The ODE solver detected an internal error.
</nierror>
<nierror code="-2338">
LabVIEW Simulation Module:  The ODE solver detected an internal error.
</nierror>
<nierror code="-2337">
LabVIEW Simulation Module:  You can linearize only simulation subsystems.
</nierror>
<nierror code="-2336">
LabVIEW Simulation Module:  The simulation diagram returned NaN to the ODE solver.
</nierror>
<nierror code="-2335">
LabVIEW Simulation Module:  The simulation diagram returned Inf to the ODE solver.
</nierror>
<nierror code="-2334">
LabVIEW Simulation Module:  An overflow occurred in the ODE solver.
</nierror>
<nierror code="-2333">
LabVIEW Simulation Module:  The step size must be between the minimum and maximum step size.
</nierror>
<nierror code="-2332">
LabVIEW Simulation Module:  The minimum step size must be less than or equal to the maximum step size.
</nierror>
<nierror code="-2331">
LabVIEW Simulation Module:  The absolute tolerance and relative tolerance cannot both be zero.
</nierror>
<nierror code="-2330">
LabVIEW Simulation Module:  The discrete step size must be an integer multiple of the step size.
</nierror>
<nierror code="-2329">
LabVIEW Simulation Module:  The simulation step size cannot be zero.
</nierror>
<nierror code="-2328">
LabVIEW Simulation Module:  You can use the Linearize Subsystem dialog box only on simulation subsystems.
</nierror>
<nierror code="-2327">
LabVIEW Simulation Module:  You can use the Linearize Subsystem dialog box only if you have created a VI under My Computer in the Project Explorer.
</nierror>
<nierror code="-2325">
LabVIEW Simulation Module:  The ODE solver did not converge at the minimum step size.
</nierror>
<nierror code="-2324">
LabVIEW Simulation Module:  The ODE solver cannot meet the error tolerance using the minimum step size.
</nierror>
<nierror code="-2323">
LabVIEW Simulation Module:  The simulation step size must be greater than zero.
</nierror>
<nierror code="-2322">
LabVIEW Simulation Module:  You selected a feedthrough behavior that is inconsistent with the specified discrete integration method.
</nierror>
<nierror code="-2321">
LabVIEW Simulation Module:  The sample rate divisor is negative or zero.
</nierror>
<nierror code="-2320">
LabVIEW Simulation Module:  This intermediate solver evaluation should not have been executed.
</nierror>
<nierror code="-2319">
LabVIEW Simulation Module:  The dimensions of the arrays for the lookup table are inconsistent.
</nierror>
<nierror code="-2318">
LabVIEW Simulation Module:  The dimensions of the parameter vectors of this function do not match.
</nierror>
<nierror code="-2317">
LabVIEW Simulation Module:  You selected a feedthrough behavior that is inconsistent with the specified discrete integration method.
</nierror>
<nierror code="-2316">
LabVIEW Simulation Module:  The order of the numerator must be greater than the order of the denominator.
</nierror>
<nierror code="-2315">
LabVIEW Simulation Module:  You must match complex entries in the Zero-Pole-Gain function with complex conjugates.
</nierror>
<nierror code="-2314">
LabVIEW Simulation Module:  For an transfer function with indirect feedthrough behavior, the order of the numerator must be less than or equal to the order of the denominator.
</nierror>
<nierror code="-2313">
LabVIEW Simulation Module:  The size of the initial condition vector is incorrect.
</nierror>
<nierror code="-2312">
LabVIEW Simulation Module:  The size of the input vector is incorrect for the MIMO system.
</nierror>
<nierror code="-2311">
LabVIEW Simulation Module:  The order of the model must not change from the previous iteration of the Simulation Loop.
</nierror>
<nierror code="-2310">
LabVIEW Simulation Module:  The dimensions of matrices A, B, C, and D are not consistent with each other.
</nierror>
<nierror code="-2309">
LabVIEW Simulation Module:  The period for this function must be greater than zero.
</nierror>
<nierror code="-2308">
LabVIEW Simulation Module:  The duty cycle must be between 0% and 100%.
</nierror>
<nierror code="-2307">
LabVIEW Simulation Module:  Evaluating a single-step solver on a minor substep.
</nierror>
<nierror code="-2306">
LabVIEW Simulation Module:  The frequency for this function must be greater than zero.
</nierror>
<nierror code="-2305">
LabVIEW Simulation Module:  The target time for the Chirp Signal function must be greater than the simulation initial time.
</nierror>
<nierror code="-2304">
LabVIEW Simulation Module:  The upper limit for the Saturation function must be greater than or equal to the lower limit.
</nierror>
<nierror code="-2303">
LabVIEW Simulation Module:  The switch on point for the Relay function must be greater than or equal to the switch off point.
</nierror>
<nierror code="-2302">
LabVIEW Simulation Module:  The quantization interval for the Quantizer function must be greater than zero.
</nierror>
<nierror code="-2301">
LabVIEW Simulation Module:  The Simulation Translator failed to properly translate an expression.
</nierror>
<nierror code="-2300">
LabVIEW Simulation Module:  Invalid SimX node reference.
</nierror>
</nidocument>